Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

SPOC

Occupied setpoint

-

50

Re-scalable

C2

MXPV

Maximum Sensor Scaling (value @10V)

-

100

Re-scalable

C3

MNPV

Minimum Sensor Scaling (value@0V)

-

0

Re-scalable

C4

DPPV

Decimal places for engineering scaling

-

1

0 to 4

C5

MXSP

Maximum setpoint value

-

100

Re-scalable

C6

MNSP

Minimum setpoint value

-

0

Re-scalable

C7

MNOP

Minimum Output

%

5

0 to 100

C8

INVL

Invert control sense:
0: increasing error reduces output
1: increasing error increases output

-

0

0 to 1

C9

ELAG

Percentage lag or lead for second output

%

0

-50 to 50

C10

HPRD

Stroke time or minimum on time for driver

Secs/10

-

1 to 60

C11

HDLY

Interlock delay:
Negative value delays fan (or pump) after heating starts
Positive value cause run on of fan after heating shuts down

Mins

0

-30 to 30

C12

CPRD

Stroke time or minimum on time for driver

Secs/10

-

1 to 60

C13

CDLY

Interlock delay:
Negative value delays fan (or pump) after cooling starts
Positive value cause run on of fan after cooling shuts down

Mins

0

-30 to 30

C14

MANL

Manual level , from Doorway

%

0

0 to 100

C15

TYPE

Pump(set) switching type:
(when regd to BLR/DIN/STD or HIL):
1: Primary Pump(s)
2: VT Pump(s)

(when regd to special BLR/DIN/DHW)
3: DHW Pump(s)

(when regd to VTC, VTU or CTU)
4: Heating Optimum Start
5: Heating Occupation only
6: Heating Demand >5%

(when regd to CLR, VTU or CTU)
7: Cooling Optimum Start
8: Cooling Occupation only
9: Cooling Demand >5%

-

1

1 to 9

C16

ACNL

Analogue Channel select:
1: select channel b terminals 5+6
2: select channel a terminals 3+4

-

0

0 to 2

C17

ALRM

Alarm mode:
0: ignore alarms
1: report alarms
2: report alarms, shut down all outputs on alarm
3: report alarms, shut down all outputs on STOP alarm or sensor fail alarm

-

0

0 to 3

C18

ALST

Not used in this application

-

1

0 to 1

C19

MXVA

Maximum Voltage output a

Vdc

10

0 to 10

C20

MNVA

Minimum Voltage output a

Vdc

0

0 to 10

C20

MXVB

Maximum Voltage output b

Vdc

10

0 to 10

C21

MNVB

Minimum Voltage output b

Vdc

0

0 to 10

Doorway / InSite Code

Label

Description

Units

Default Value

Range

I2 (C31)

OCCD

Occupied

-

-

0 to 1

I3 (C32)

WMUP

Optimum Start

-

-

0 to 1

I6 (C35)

RLYA

Triac A Status (special order 3T versions only)

-

-

0 to 1

I7 (C36)

RLYB

Triac B Status (special order 3T versions only)

-

-

0 to 1

I8 (C37)

RLYC

Triac C Status (special order 3T versions only)

-

-

0 to 1

W1 (C38)

AUTO

Automatic/Manual Status

-

-

0 to 1

W2 (C39)

OVRD

Override

-

-

0 to 1

W5 (C42)

HAND

Manual Hand; use with MANL to set output level

-

0

0 to 1

W6 (C43)

POT

not used in this application

-

1

0 to 1

W7 (C44)

SERV

Service Pin Message (to Doorway and InSite, self resetting)

-

-

0 to 1

S1* (C50)

PVKP

Pressure reading

-

-

Re-scalable

S2* (C51)

HCOP

Control output to drivers

%

-

-100 to 100

S3 (C52)

RQKP

Controller current setpoint

-

-

Re-scalable

S4 (C53)

DMND

Speed

%

-

0 to 100

K1 (C60)

SPOC

Occupied setpoint

-

50

Re-scalable

K2 (C61)

MXPV

Maximum Sensor Scaling (value @10V)

-

100

Re-scalable

K3 (C62)

MNPV

Minimum Sensor Scaling (value@0V)

-

0

Re-scalable

K4 (C63)

DPPV

Decimal places for engineering scaling

-

1

0 to 4

Engineering Parameters; only accessible via Doorway and InSite

C90

NOAL

No Alarms; all alarms cleared when set to 1

-

-

0 or 1

C91

SENF

Sensor Failed (when set to 1)

-

-

0 or 1

C92

EXTN

Volt-Free Contact alarm (when set to 1)

-

-

0 or 1

C93

STOP

STOP alarm received (when set to 1)

-

-

0 or 1

* 24 hour plots available for these values by default

Plotting interval and plotted variable changeable via Doorway or InSite