Doorway / InSite Code |
Label |
Description |
Units |
Default Value |
Range |
C1 |
CHNL |
The number of the channel to be configured
1 - 5 Hardware Inputs also (known as 'A' to 'E') |
- |
- |
1 to 5 |
C2 |
CTYP |
Selected Hardware Input Channel type
0: Analogue
1: Digital |
- |
0 |
0 to 1 |
C3 |
CDP |
Selected Hardware Input channel decimal place. This
also specifies the range of the measured variable.
0: -9999 to +9999
1: -999.9 to +999.9
2: -99.99 to +99.99
3: -9.999 to +9.999 |
- |
0 |
0 to 3
|
C4 |
CTOP |
Selected Hardware Input Channel Engineering value
at 10V |
- |
0 |
-9999 to +9999 |
C5 |
CBTM |
Selected Hardware Input Channel Engineering value
at 0V |
- |
0 |
-9999 to +9999 |
C6 |
CLOW |
Low alarm level for selected input channel', (* see
issue note for delays and deadbands) |
- |
0 |
-9999 to +9999 |
C7 |
CLDY |
Delay before alarm generation, after measured level
falling below CLOW:
0: Hysteresis operation
>0: Delay in minutes before alarm action |
Mins |
2 |
0 to 30
|
C8 |
CHGH |
High alarm level for selected input channel.
|
- |
0 |
-9999 to +9999 |
C9 |
CHDY |
Delay before alarm generation, after measured level
rising above CHGH:
0: Hysteresis operation
>0: Delay in minutes before alarm action |
Mins |
2 |
0 to 30
|
C10 |
CAON |
Selected input channel alarm on condition:
0: No alarms
1: on low alarm
2: on high alarm
3: on high and low alarm
|
- |
-
|
0 to 3 |
C11 |
C OS
|
Applies an offset to the currently selected channel,
+/- 50% of the sensor measuring range. (See note on channel failure tests) |
- |
- |
- |
C12 |
C NS
|
Set the 'heathy state' of the currently selected
input if configured as a digital input.(Set by default to the state of
the input when configured.) |
- |
0 |
0 to 1 |
C13 |
COPY |
Copy the currently selected channel setup to channel
'x'. |
- |
0 |
0 to 5 |
C14 |
DLYO |
Alarm delay on, sets delay edge for all 'CAON', TAON,
etc:
0: Delay action on alarm condition (ie. Alarm delayed on input exceeding
limits, but clears immediately.)
1: Delay action on alarm and clearing (ie. Alarm delayed on input exceeding
limits, and delays on clearing.)
2: Delay action on clearing. (ie. Alarm reported immediatly on input exceeding
limits, but delays on clearing.)
|
- |
0 |
0 to 2 |
C15 |
ASAC |
All stop action. On receipt of 'All Stop' alarm
0: No alarm reporting, no alarms to relays
1: Relays function, but No alarms to doorway
2: All Stop ignored |
- |
0 |
0 to 2 |
C16 |
TLOW |
Low alarm level for remote devices average temperature
measurement |
Deg C |
0 |
5 to 65 |
C17 |
TLDY |
Delay before alarm generation, after measured level
falling below TLOW:
0: Hysteresis operation
>0: Delay in minutes before alarm action
|
Mins |
2 |
0 to 30 |
C18 |
THGH |
High alarm level for remote devices average temperature
measurement. |
Deg C |
0 |
-9999 to +9999 |
C19 |
THDY |
Delay before alarm generation, after measured level
rising above THGH:
0: Hysteresis operation
>0: Delay in minutes before alarm action
|
Mins |
0 |
0 to 30 |
C20 |
TAON |
Temperature alarm on condition:
0: No alarms
1: on low alarm
2: on high alarm
3: on high and low alarm |
- |
0 |
0 to 3 |
C21 |
HLOW |
Low alarm level for remote devices average humidity
measurement. |
%RH |
0 |
5 to 95 |
C22 |
HLDY |
Delay before alarm generation, after measured level
falling below HLOW:
0: Hysteresis operation
>0: Delay in minutes before alarm action
|
Mins |
2 |
0 to 30 |
C23 |
HHGH |
High alarm level for remote devices average humidity
measurement. |
%RH |
0 |
5 to 95 |
C24 |
HHDY |
Delay before alarm generation, after measured level
rising above CHGH:
0: Hysteresis operation
>0: Delay in minutes before alarm action
|
Mins |
2 |
0 to 30 |
C25 |
HAON |
Humidity alarm on condition:
0: No alarms
1: on low alarm
2: on high alarm
3: on high and low alarm.
|
- |
0 |
0 to 3 |
C26 |
RSAM |
Remote sensor alarm mute
0: Report remote sensors status online/offline
1: Do not report remote sensor status
With the mute TRUE the condition of the remote sensors can still be monitored
by checking the NSEN bit C99 which will be TRUE if any remote device has
a fault. |
- |
1 |
0 to 1 |
C27 |
MAMX |
Send the following parameter Temperature and Humidity
to (AHU, etc) and display on S6 S7:
0: Minimum value
1: Average value
2: Maximum value |
- |
0 |
0 to 2 |
C28 |
GNAS |
Generate System 'STOP' Alarm:
0: Do NOT generate STOP.
1: First Input Only generates STOP.
2: ALL Inputs generate STOP. |
- |
0 |
0 to 2 |
C29 |
LMCA |
Latching mode for Common alarm on channel alarm
condition.
(Reset - here means RCLR switch W5 or the common alarm reset input channel
I6 - ARST).
0: Channel and common alarm output will latch on, can be reset only once
the alarm has cleared.
1: Channel and common alarm output will latch on, common can be disabled
by reset. Common alarm will be bourght back on by any channel changing
its current state, i.e alarm or clear.
2: Channel and common alarm output will latch on, common can be disabled
by reset. Common alarm will be bourght back on by any channel going into
its alarm state. Any channels that are in alarm (when reset) will clear
at that time if no longer in alarm, or will clear without event when that
channel alarm condition clears.
3: No latching of channel or common alarm outputs, output will clear when
alarm condition on input clears. Common alarm will be on if any channel
is in alarm condition. |
- |
0 |
0 to 3 |
Doorway / InSite Code |
Label |
Description |
Units |
Default Value |
Range |
I1 (C30)
|
IN A |
Input 'A' Status if digital |
- |
- |
0 to 1 |
I2 (C31)
|
IN B |
Input 'B' Status if digital
|
- |
- |
0 to 1 |
I3 (C32)
|
IN C |
Input 'C' Status if digital
|
- |
- |
0 to 1 |
I4 (C33)
|
IN D |
Input 'D' Status if digital
|
- |
- |
0 to 1 |
I5 (C34)
|
IN E |
Input 'E' Status if digital
|
- |
- |
0 to 1 |
I6 (C35)
|
ARST |
Alarm reset input status |
- |
- |
0 to 1 |
W1 (C38)
|
AUTO
|
Automatic/Manual Status
|
- |
1 |
0 to 1 |
W2 (C39)
|
OVRD
|
Override
|
- |
- |
0 to 1 |
W3 (C40) |
NALM
|
No Alarms - Use as MUTE durring commission phase,
no alarms to Doorway:
0: Alarm reporting enabled
1: Mute all |
- |
0 |
0 to 1 |
W4 (C41) |
CALM
|
Common Alarm - Enables the common alarm output, with
this enabled the alarm relay will latch and must be reset manually by
the 'Reset input' or by setting 'RCLR':
0: Common alarm disabled
1: common alarm enabled |
- |
0 |
0 to 1 |
W5 (C42) |
RCLR |
Allow remote reset of common alarm from Doorway.
1: Reset (Self clearing) |
- |
0
|
0 to 1 |
W6 (C43) |
RPLN |
Replace missing nodes in database
1: Auto replace node |
- |
1 |
0 to1 |
W7 (C44)
|
SERV
|
Service Pin Msg (to Doorway +InSite, self resetting)
|
- |
0 |
0 to 1 |
W8 (C45)
|
CGST
|
Configuration Mode Status
|
- |
0 |
0 to 1 |
S1* (C50) |
IN A |
Input 'A' Value |
- |
- |
- |
S2* (C51)
|
IN B |
Input 'B' Value |
- |
- |
- |
S3* (C52)
|
IN C |
Input 'C' Value |
- |
- |
- |
S4 (C53)
|
IN D |
Input 'D' Value |
- |
- |
- |
S5 (C54) |
IN E |
Input 'E' Value |
- |
- |
- |
S6 (C55)
|
NS T
|
(Max/Min/Ave) Temperature value of remote sensors |
Deg C |
- |
- |
S7 (C56)
|
NS H
|
(Max/Min/Ave) Humidity value of remote sensors |
%RH |
- |
0 to 100 |
|
|
Engineering Parameters; only accessible via Doorway
and InSite |
|
|
|
C90
|
NOAL
|
No Alarms; all alarms cleared when set to 1
|
- |
- |
0 or 1 |
C91
|
ALMA |
Input 'A' Alarm state |
- |
- |
0 or 1 |
C92
|
ALMB |
Input 'B' Alarm state |
- |
- |
0 or 1 |
C93
|
ALMC |
Input 'C' Alarm state |
- |
- |
0 or 1 |
C94
|
ALMD |
Input 'D' Alarm state |
- |
- |
0 or 1 |
C95
|
ALME |
Input 'E' Alarm state |
- |
- |
0 or 1 |
C96 |
NS T |
Temperature alarm remote devices (S 6) |
- |
- |
0 to 24 |
C97 |
NS H |
Humidity alarm remote devices (S 7) |
- |
- |
0 to 24 |
C98 |
CMAL |
Common Alarm state |
- |
- |
1 to 24 |
C99 |
NSEN |
Remote networked measuring device fault |
- |
- |
0 to 4 |
|
|
* 24 hour plots available for these values by default |
|
|
|
|
|
Plotting interval and plotted variable changeable
via Doorway or InSite |
|
|
|
