Doorway / InSite Code
|
Label
|
Description
|
Units
|
Default Value
|
Range
|
C1
|
SACT
|
Sensor Action; sets pre-processing for temperature inputs:
0: use either sensor for control
1: average of valid sensor values
2: maximum of valid sensor values
3: minimum of valid sensor values
|
-
|
0
|
0 to 3
|
C2
|
SPTY
|
Setpoint Type, control mode:
1: Driver only demand-based control
2: Temperature control, Heat/Cool demands from Zone Controllers and/or
Fan Coils derive a setpoint using MAXH, MINH, MAXC, MINC
|
-
|
0
|
0 to 2
|
C3
|
INMD
|
Input Mode for use of terminals 9-10, input c:
0: Feature disabled, used for temperature sensing
1: External occupation (input linked = Occupied) AND with internal Occupation
2: External occupation (input linked = Occupied) OR with internal Occupation
3: External Occupation signal only
4: Alarm input
5: Rivermill Project Heat Pump fan speed switch
|
-
|
0
|
0 to 5
|
C4
|
MAXH
|
Maximum Supply Heating setpoint (used with SPTY = 2)
|
Deg C
|
30
|
0 to 90
|
C5
|
MINH
|
Minimum Supply Heating setpoint (used with SPTY = 2)
|
Deg C
|
20
|
0 to 90
|
C6
|
MAXC
|
Maximum Supply Cooling setpoint (used with SPTY = 2)
|
Deg C
|
18
|
2 to 30
|
C7
|
MINC
|
Minimum Supply Heating setpoint (used with SPTY = 2)
|
Deg C
|
10
|
2 to 30
|
C8
|
MIND
|
Supply minimum demand, used for switching between heating and cooling
|
%
|
4
|
0 to 10
|
C9
|
OCCO
|
When set controller will only run during the occupied period
|
-
|
0
|
0 to 1
|
C10
|
HPRD
|
Heating period, stroke time of valve or minimum on time
|
Secs/10
|
-
|
1 to 60
|
C11
|
HDLY
|
Interlock delay:
Negative value delays fan (or pump) after heating starts
Positive value cause run on of fan after heating shuts down
|
Mins
|
0
|
-30 to 30
|
C12
|
CPRD
|
Cooling period, stroke time of valve or minimum on time
|
Secs/10
|
-
|
1 to 60
|
C13
|
CDLY
|
Interlock delay:
Negative value delays fan (or pump) after cooling starts
Positive value cause run on of fan after cooling shuts down
|
Mins
|
0
|
-30 to 30
|
C14
|
FPRD
|
Fan period, minimum time to change fan speed steps
|
Secs/10
|
12
|
1 to 60
|
C15
|
FRPT
|
Frost protection:
0: no action
1: open heating valve 50%
2: open heating valve and run pump/fan
|
-
|
0
|
0 to 2
|
C16
|
MANL
|
Manual level , from Doorway
|
%
|
0
|
-100 to 100
|
C17
|
MXCT
|
Maximum CT to Boiler
|
Deg C
|
70
|
20 to 100
|
C18
|
MNCT
|
Minimum CT to Boiler
|
Deg C
|
50
|
20 to 100
|
C19
|
ALRM
|
Alarm mode:
0: ignore alarms
1: report alarms
2: report alarms, shut down all outputs on alarm
3: report alarms, shut down all outputs on STOP alarm or sensor fail alarm
|
-
|
1
|
0 to 3
|
C20
|
ALST
|
Defines the state of the input which is considered to be the alarm condition
|
-
|
0
|
0 to 1
|
C21
|
TRND
|
When set sends Heat Demand, Cool Demand and Outside Temperature to SLT
for onward transmission to TREND outstation(s) (see Serial Adaptor for
details)
|
-
|
0
|
0 to 70
|
C22
|
DOMN
|
Own Domain
|
-
|
1
|
0 to 8
|
C23
|
HTSC
|
Heat source; points Energy Demand to source of Heat energy
|
-
|
0
|
-1 to 250
|
C24
|
CLSC
|
Cool source; points Energy Demand to source of Cool energy
|
-
|
0
|
-1 to 250
|
C25
|
OCDS
|
Occupation destination; points Occupancy Demand at another controller
|
-
|
0
|
0 to 250
|
C26
|
HTCT
|
if non zero send value as Heating CT setpoint
|
Deg C
|
0
|
0 to 100
|
C27
|
CLCT
|
if non zero send value as Cooling CT setpoint
|
Deg C
|
0
|
0 to 20
|
Doorway / InSite Code
|
Label
|
Description
|
Units
|
Default Value
|
Range
|
I1 (C30)
|
INPA
|
Input A
|
-
|
-
|
0 to 1
|
I2 (C31)
|
INPB
|
Input B
|
-
|
-
|
0 to 1
|
I3 (C32)
|
RLYA
|
Relay A (heating stage 1)
|
-
|
-
|
0 to 1
|
I4 (C33)
|
RLYB
|
Relay B (heating stage 2)
|
-
|
-
|
0 to 1
|
I5 (C34)
|
RLYC
|
Relay C (heating stage 3)
|
-
|
-
|
0 to 1
|
I6 (C35)
|
RLYD
|
Relay D (cooling stage 1)
|
-
|
-
|
0 to 1
|
I7 (C36)
|
RLYE
|
Relay E (cooling stage 2)
|
-
|
-
|
0 to 1
|
I8 (C37)
|
RLYF
|
Relay F (cooling stage 3)
|
-
|
-
|
0 to 1
|
W1 (C38)
|
AUTO
|
Automatic/Manual Status
|
-
|
-
|
0 to 1
|
W2 (C39)
|
OVRD
|
Override
|
-
|
-
|
0 to 1
|
W3 (C40)
|
MISN
|
Generate an alarm if any node detected as missing
|
-
|
0
|
0 to 1
|
W4 (C41)
|
RPLN
|
When registering a new node replace missing nodes
|
-
|
1
|
0 to 1
|
W5 (C42)
|
HAND
|
Manual Hand; use with MANL to set output level
|
-
|
0
|
0 to 1
|
W7 (C44)
|
SERV
|
Service Pin Msg (to Doorway +InSite, self resetting)
|
-
|
0
|
0 to 1
|
W8 (C45)
|
CGST
|
Configuration Mode Status
|
-
|
-
|
0 to 1
|
S1* (C50)
|
SPLA
|
Temperature Sensor 1 (controlled medium)
|
Deg C
|
-
|
5 to 35
|
S2* (C51)
|
RTNA
|
Temperature Sensor 2 (controlled medium)
|
Deg C
|
-
|
5 to 35
|
S3 (C52)
|
HCOP
|
Heat Cool Output to Drivers (cooling negative)
|
Deg C
|
-
|
5 to 35
|
S4 (C53)
|
OUTS
|
Outside Temperature
|
%
|
-
|
-100 to 100
|
S5 (C54)
|
SPSL
|
Supply (off coil) setpoint
|
Deg C
|
-
|
5 to 35
|
S6 (C55)
|
HDMD
|
Heat Demand from return loop or from Zone Controller
|
%
|
-
|
0 to 100
|
S7 (C56)
|
CDMD
|
Cool Demand from return loop or from Zone Controller
|
%
|
-
|
0 to 100
|
S8 (C57)
|
OUTH
|
Outside Relative Humidity (from Intelligent T+RH sensor)
|
%
|
-
|
5 to 95
|
S9 (C58)
|
PRHT
|
Priority Heating Zone number
|
-
|
0
|
0 to 200
|
S10 (C59)
|
PRCL
|
Priority Cooling Zone Number
|
-
|
0
|
0 to 200
|
K1 (C60)
|
SPOC
|
Occupied setpoint
|
Deg C
|
20
|
5 to 35
|
K2 (C61)
|
SPNO
|
Non Occupied setpoint
|
Deg C
|
10
|
5 to 35
|
K3 (C62)
|
SPSV
|
Supervised setpoint from Master controller
|
Deg C
|
-
|
0 to 35
|
K4 (C63)
|
SPTR
|
Setpoint Trim
|
Deg C
|
0
|
-10 to 10
|
|
|
Engineering Parameters; only accessible via Doorway and InSite
|
|
|
|
C90
|
NOAL
|
No alarms ; all alarms cleared when set to 1
|
-
|
-
|
0 or 1
|
C91
|
GENA
|
General Alarm (input a) (when set to 1)
|
-
|
-
|
0 or 1
|
C92
|
GENB
|
General Alarm (input b) (when set to 1)
|
-
|
-
|
0 or 1
|
C93
|
FREZ
|
Danger of Freezing Alarm (when set to 1)
|
-
|
-
|
0 or 1
|
C94
|
STOP
|
Stop alarm (when set to 1)
|
-
|
-
|
0 or 1
|
C95
|
OUTF
|
Outside Sensor Fail (when set to 1)
|
-
|
-
|
0 or 1
|
C96
|
FROS
|
Frost Protection in operation (when set to 1)
|
-
|
-
|
0 or 1
|
|
|
* 24 hour plots available for these values by default
|
|
|
|
|
|
Plotting interval and plotted variable changeable via Doorway or InSite
|
|
|
|
