Configuration Tables

Pool Controller

Configuration Tables

Doorway / InSite Code	Label	Description	Units	Default Value	Range
C1	SACT	Sensor Action 0: Use input 5-6 ’temp’ for Pool temp sensor, input 3-4 for VFC 1: Use average of valid sensor values 2: Use maximum of valid sensor values 3: Use minimum of valid sensor values 4: Use remote sensor as Occupation input , shorted is occupied 5: Use networked temperature (nviRemoteTemp) if valid, else remote hardwired if valid, else local 6: Use remote sensor as PIR input, shorted is occupied with close control. open circuit is standby or non-occupied according to zone occupancy pattern	-	0	0 to 6
C2	SCAL	Calibrate sensor value	Deg C	0	-5 to 5
C3	SPMD	Midpoint of absolute setpoint adjustment range	Deg C	30	5 to 95
C4	SPRG	Range of absolute setpoint adjustment about midpoint	Deg C	5	0 to 10
C5	SPDB	Setpoint deadband between heating and cooling setpoints. If zero disables cooling	Deg C	0	0 to 10
C6	SBDB	Additional deadband used in Standby Mode and Optimum off	Deg C	2	0 to 10
C7	SPTY	Setpoint type 0: use local setpoint 1: use remote setpoint (from supervising Zone Controller), disable local OSS	-	0	0 to 1
C8	XHRS	Extension hours when override pressed outside occupation	Hrs	1	0 to 8
C9	FRSE	Fabric/frost rise; added to SPNO to form termination temperature for heating run if temperature dips below SPNO value during non-occupation	Deg C	0	0 to 10
C10	MIND	Minimum demand to maintain Occupancy output for pump	%	0	0 to 10
C11	OCCO	Run during occupancy only 0: run during occupancy, OSS and frost 1: run during ocupancy only	-	0	0 to 1
C12	HPRD	Heating valve period or minimum on time	Secs/10	-	1 to 60
C13	HDLY	Heating Interlock Delay negative value delays fan (or pump) after heating starts positive value cause run on of fan after heating shuts down	Mins	0	-30 to 30
C14	CPRD	Cooling valve period or minimum on time	Secs/10	-	1 to 60
C15	CDLY	Cooling Interlock delay negative value delays fan (or pump) after cooling starts positive value cause run on of fan after cooling shuts down	Mins	0	-30 to 30
C16	FPRD	Not used in this application	Secs/10	12	1 to 60
C17	FRPT	Frost protect 0: no action 1: open heating valve 50% 2: open heating valve and run pump/fan	-	0	0 to 2
C18	MANL	Manual level , from Doorway	%	0	-100 to 100
C19	ALRM	Alarm mode 0: Ignore alarms 1: Report alarms 2: Report alarms, shut down all outputs on alarm 3: Report alarms, shut down all outputs on STOP alarm or sensor fail alarm	-	1	0 to 3
C20	ALST	Alarm report sense 0: Alarm if input = 0 (contact open), healthy if input = 1 (closed) 1: Alarm if input = 1 (contact closed), healthy if input = 0 (open)	-	0	0 to 1
C21	HTSC	Heat Source; points Energy Demand to source of Heating energy	-	1	0 to 8255
C22	CLSC	Not used in this application		0	0 to 8255
C23	OCDS	Occupation Destination: points Occupancy Demand at another controller	-	0	0 to 8255
C24	HTCT	Setpoint selector 0: send Heating Demand signal as % >0: CT Setpoint, send Heating Demand as CT setpoint only accepted by Primary Boiler Controller set temperature required from boiler (for CT Circuit Control)	Deg C	0	0 to 100
C25	CLCT	Reserved for future use	Deg C	0	0 to 20
C26	ISS3	Set to force single domain operation (should only be needed when using issue 3 Floor Controllers)	-	0	0 to 1

Monitoring Parameters

Doorway / InSite Code	Label	Description	Units	Default Value	Range
I1 (C30)	FRST	Frost Protection Mode (SPNO violated)	-	-	0 to 1
I2 (C31)	OCC	Occupied	-	-	0 to 1
I3 (C32)	OSRT	Optimum Start in operation	-	-	0 to 1
I4 (C33)	OOFF	Optimum Off in operation	-	-	0 to 1
I5 (C34)	COOL	Controller in cooling mode	-	-	0 to 1
I6 (C35)	COND	Condensation detected	-	-	0 to 1
I8 (C37)	XOCC	External Occupation signal	-	-	0 to 1
W1 (C38)	AUTO	Automatic/Manual Status	-	-	0 to 1
W2 (C39)	OVRD	Override	-	-	0 to 1
W5 (C42)	HAND	Manual Hand; use with MANL to set output level	-	0	0 to 1
W8 (C45)	CGST	Configuration Mode Status	-	-	0 to 1
S1* (C50)	ROOM	Controller measured temperature	Deg C	-	5 to 30
S2* (C51)	DMND	Control Demand	%	-	-100 to 100
S3 (C52)	REQD	Controller current setpoint	Deg C	-	5 to 30
S4 (C53)	HTOP	Heating Output to driver	%	-	0 to 100
S5 (C54)	CLOP	Cooling Output to driver	%	-	0 to 100
S6 (C55)	RHUM	Relative Humidity (Not used in this application)	%	-	0 to 100
S7 (C56)	OPST	Last Optimum Start time	hours	-	0 to 24
S8 (C57)	OPOK	Last Optimum Start complete (OK)	hours	-	0 to 24
K1 (C60)	SPOC	Occupation Setpoint	Deg C	20	10 to 30
K2 (C61)	SPNO	Non-Occupation Setpoint	Deg C	10	5 to 30
K3 (C62)	SPSV	Supervised Setpoint from Master Controller	Deg C	-	0 to 30
K4 (C63)	SPRH	Humidity protection setpoint (Not used in this application)	Deg C	0	0 to 95
K5 (C64)	MXOS	Maximum Optimum Start time	hours	6	1 to 24
K6 (C65)	MXOF	Maximum Optimum Stop time	hours	2	0 to 4
K7 (C66)	NOSV	Non Occupied Supervised setpoint	Deg C	0	0 to 30
		Engineering Parameters; only accessible via Doorway and InSite
C90	NOAL	No alarms; all alarms cleared when set to 1	-	-	0 or 1
C91	SENF	Sensor fail alarm (when set to 1)	-	-	0 or 1
C92	RPVF	Remote PV fail alarm (when set to 1)	-	-	0 or 1
C93	STOP	Stop alarm received (when set to 1)	-	-	0 or 1
		* 24 hour plots available for these values by default
		Plotting interval and plotted variable changeable via Doorway or InSite

Pool Controller

Configuration Tables

Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

SACT

-

0

0 to 6

C2

SCAL

Calibrate sensor value

Deg C

0

-5 to 5

C3

SPMD

Midpoint of absolute setpoint adjustment range

Deg C

30

5 to 95

C4

SPRG

Range of absolute setpoint adjustment about midpoint

Deg C

5

0 to 10

C5

SPDB

Setpoint deadband between heating and cooling setpoints. If zero disables cooling

Deg C

0

0 to 10

C6

SBDB

Additional deadband used in Standby Mode and Optimum off

Deg C

2

0 to 10

C7

SPTY

Setpoint type 0: use local setpoint 1: use remote setpoint (from supervising Zone Controller), disable local OSS

-

0

0 to 1

C8

XHRS

Extension hours when override pressed outside occupation

Hrs

1

0 to 8

C9

FRSE

Fabric/frost rise; added to SPNO to form termination temperature for heating run if temperature dips below SPNO value during non-occupation

Deg C

0

0 to 10

C10

MIND

Minimum demand to maintain Occupancy output for pump

%

0

0 to 10

C11

OCCO

Run during occupancy only 0: run during occupancy, OSS and frost 1: run during ocupancy only

-

0

0 to 1

C12

HPRD

Heating valve period or minimum on time

Secs/10

-

1 to 60

C13

Setpoint type
0: use local setpoint
1: use remote setpoint (from supervising Zone Controller), disable local OSS

Run during occupancy only
0: run during occupancy, OSS and frost
1: run during ocupancy only

Heating Interlock Delay
negative value delays fan (or pump) after heating starts
positive value cause run on of fan after heating shuts down

Cooling Interlock delay
negative value delays fan (or pump) after cooling starts
positive value cause run on of fan after cooling shuts down

Frost protect
0: no action
1: open heating valve 50%
2: open heating valve and run pump/fan

Alarm mode
0: Ignore alarms
1: Report alarms
2: Report alarms, shut down all outputs on alarm
3: Report alarms, shut down all outputs on STOP alarm or sensor fail alarm

Alarm report sense
0: Alarm if input = 0 (contact open), healthy if input = 1 (closed)
1: Alarm if input = 1 (contact closed), healthy if input = 0 (open)

Occupation Destination:
points Occupancy Demand at another controller

Setpoint selector
0: send Heating Demand signal as %
>0: CT Setpoint, send Heating Demand as CT setpoint only accepted by Primary Boiler Controller set temperature required from boiler (for CT Circuit Control)