Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

SPOC

Occupied Setpoint

-

50

Rescalable

C2

MXPV

Maximum Sensor Scaling (value at 10V)

-

100

Rescalable

C3

MNPV

Minimum Sensor Scaling (value at 0V)

-

0

Rescalable

C4

DPPV

Decimal places for engineering scaling

-

1

0 to 4

C5

MXSP

Maximum setpoint value

-

100

Rescalable

C6

MNSP

Minimum setpoint value

-

0

Rescalable

C7

MNOP

Minimum Output

%

5

5 to 100

C8

INVL

Invert control sense
0: increasing error reduces output
1: increasing error increases output

-

0

0 to 1

C9

ELAG

Percentage lag or lead for extract fan

%

0

-50 to 50

C10

HPRD

Not used in this application

Secs/10

0

1 to 60

C11

HDLY

Not used in this application

Mins

0

-30 to 30

C12

CPRD

Not used in this application

Secs/10

0

1 to 60

C13

CDLY

Not used in this application

Mins

0

-30 to 30

C14

MANL

Manual level , from Doorway

%

0

0 to 100

C15

TYPE

Fan type;
1: supply,
2: extract

-

1

1 to 2

C16

ACHL

Analogue Channel select;
1:use channel b terminals 5+6
2:use channel a terminals 3+4

-

2

1 to 2

C17

ALRM

Alarm mode;
0: ignore alarms
1: report alarms
2: report alarms, shut down all outputs on alarm
3: report alarms, shut down all outputs
on STOP alarm or sensor fail alarm

-

0

0 to 3

C18

ALST

Not used in this application

C189

MXVA

Maximum Voltage output a (for AOP types only)

V

10

0 to 10

C20

MNVA

Minimum Voltage output a (for AOP types only)

V

0

0 to 10

C21

MXVB

Maximum Voltage output b (for AOP types only)

V

10

0 to 10

C22

MNVB

Minimum Voltage output b (for AOP types only)

V

0

0 to 10

Doorway / InSite Code

Label

Description

Units

Default Value

Range

I2 (C31)

OCCD

Occupied

-

-

0 to 1

W1 (C38)

AUTO

Automatic/Manual Status

-

-

0 to 1

W2 (C39)

OVRD

Override

-

-

0 to 1

W3 (C40)

POT

When set specifies that special order potentiometer fitted, do not set unless your hardware has the potentiometer

-

0

0 to 1

W5 (C42)

HAND

Manual Hand; use with MANL to set output level

-

0

0 to 1

W7 (C44)

SERV

Service Pin Msg (to Doorway +InSite, self resetting)

-

-

0 to 1

W1 and W2 used together with Doorway Auto/Manual dialog box

S1* (C50)

PVKP

Pressure reading (or other measured value e.g CO2)

-

-

Rescaleable

S2* (C51)

HCOP

Controller output (shows demand to drivers,)
Positive reading : Direct-acting loop (e.g.Pressure)
Negative reading: Reverse acting loop (e.g CO2 control)

%

-

-100 to 100

S3 (C52)

RQKP

Controller current setpoint

-

-

Rescaleable

S4 (C53)

DMND

Demand to Fan Speed Control

%

-

0 to 100

K1 (C60)

SPOC

Pressure setpoint

-

50

Rescaleable

K2 (C61)

DPPV

Decimal point for re-scalable engineering units

-

1

0 to 4

K4 (C63)

MXPV

Maximum sensor scaling

-

100

Rescaleable

K5 (C64)

MNPV

Minimum sensor scaling

-

0

Rescaleable

K6 (C65)

NPSD

Night Purge Speed.

If set to a non zero value the controller will drive the output to this value while its AHU is in Night Purge mode. Allows the full volume of the fans to be used when NIght cooling.

%

0

0 to 100

C90

NOAL

No alarm

-

-

0 to 1

C91

SENF

Sensor fail

-

-

0 to 1

C92

EXTN

Alarm for external input

-

-

0 to 1

C93

STOP

STOP alarm received

-

-

0 to 1

* 24 hour plots available for these values by default

Plotting interval and plotted variable changeable via Doorway or InSite