Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

SPRH

Occupied setpoint

%RH

50

0 to 100

C2

SPMD

Midpoint of setpoint adjustment range

%

50

10 to 90

C3

SPRG

Range of setpoint adjustment about midpoint

%

20

0 to 40

C4

SPDB

Setpoint deadband between humidification and de_humidification setpoints. If zero disables de-hum

%

10

0 to 20

C5

RDLY

Recirculation delay , for use with evaporative coolers on Dessicant Plant;
hours of continuous running before water recircualtion is allowed

Hours

2

0 to 10

C6

HPRD

Minimum on time for humidifier stages

Secs/10

1 to 60

C7

HDLY

Not used in this application

Mins

0

-30 to 30

C8

CPRD

Not used in this application

Secs/10

1 to 60

C9

CDLY

Not used in this application

Mins

0

-30 to 30

C10

FPRD

Not used in this application

Secs/10

12

1 to 60

C11

MIND

Minimum demand

%

4

0 to 100

C12

MANL

Manual level , from Doorway

%

0

-100 to 100

C13

ALRM

Alarm mode
0 ignore alarms
1 report alarms
2 report alarms, shut down all outputs on alarm
3 report alarms, shut down all outputs on STOP alarm or sensor fail alarm

-

1

0 to 3

C14

ALST

Not used in this application

-

0

0 to 1

C15

CMDE

Control mode
0 driver only mode
1 closed loop control of humidity
2 closed loop control of Humidity and DeHum (see Close Control for setup details)

-

0

0 to 2

C16

MXSH

Maximum Supply Humidity setpoint

%RH

60

0 to 100

C17

MNSH

Minimum Supply Humidity setpoint

%RH

40

0 to 100

C18

DHOF

Supply DeHum setpoint offset

%RH

2

0 to 10

Engineering Parameters for advanced applications: contact SeaChange for further details

C19

TRGT

Target mean value for Humidifier control minimum output

%

10

3 to 100

C20

ICGN

InterCoil setpoint Gain (controls rate of adjustment)

-

10

1 to 255

C21

ICSP

InterCoil temperature setpoint for monitoring

Deg C

30

0 to 50

C22

ICLT

InterCoil temperature for monitoring

Deg C

-

0 to 50

C23

ICOP

InterCoil loop output for monitoring

%

-

0 to 100

C24

RTMD

Return Mode, provides extra control features when using cascade control
0 cascade control disabled
1 cascade control enabled (must have both Supply and return RH sensors)
2 cascade control enabled, return loop output locked if supply loop reaches 0 or 100% to prevent wind up.

-

0

0 to 2

C25

PROP

Proportional gain term for Humidity control loop

-

0

0 to 250

C26

MXVA

Maximum Voltage output a (for AOP types only)

V

10

0 to 10

C27

MNVA

Minimum Voltage output a (for AOP types only)

V

0

0 to 10

C28

MXVB

Maximum Voltage output b (for AOP types only)

V

10

0 to 10

C29

MNVB

Minimum Voltage output b (for AOP types only)

V

0

0 to 10

Doorway / InSite Code

Label

Description

Units

Default Value

Range

I2 (C31)

OCC

Occupied

-

-

0 to 1

I3 (C32)

OSRT

Optimim Start

-

-

0 to 1

I6 (C35)

RLYA

Triac A Status

-

-

0 to 1

I7 (C36)

RLYB

Triac B Status

-

-

0 to 1

I8 (C37)

RLYC

Triac C Status

-

-

0 to 1

W1 (C38)

AUTO

Automatic/Manual Status

-

-

0 to 1

W2 (C39)

OVRD

Override

-

-

0 to 1

W8 (C45)

CGST

Configuration mode

-

-

0 to 1

W1 and W2 used together with Doorway Auto/Manual dialog box

S1* (C50)

RTRH

Return Relative Humidity

%RH

-

0 to 100

S2* (C51)

SLRH

Supply Relative Humidity

%RH

-

0 to 100

S3 (C52)

DMND

Return Loop output

%

-

-100 to 100

S4 (C53)

RTSP

Return Humidity Setpoint

%RH

-

0 to 100

S5 (C54)

SLSP

Supply Humidity Setpoint

%RH

-

0 to 100

S6 (C55)

HDMD

Humidification output demand

%

-

0 to 100

S7 (C56)

CDMD

De-humudification output demand

%

-

0 to 100

S8 (C57)

RDMD

Recirculation demand

%

-

0 to 100

S9 (C58)

HTIP

Heat demand from AHU

%

-

0 to 100

S10 (C59)

CLIP

Cool demand from AHU

%

-

0 to 100

K1 (C60)

SPRH

Occupied setpoint

%RH

50

0 to 100

* 24 hour plots available for these values by default

Plotting interval and plotted variable changeable via Doorway or InSite