Doorway / InSite Code
|
Label
|
Description
|
Units
|
Default Value
|
Range
|
C1
|
OCSP
|
Occupied setpoint
|
Deg C
|
-
|
0.5 to 35
|
C2
|
SACT
|
Sensor Action; for future use; set to 0 for this application
|
-
|
0
|
0 to 3
|
C3
|
DEGR
|
Maximum temperature rise across battery with heating at 100%
|
Deg C
|
10
|
5 to 50
|
C4
|
SPFR
|
Frost or non occupied setpoint
|
Deg C
|
-
|
0 to 20.0
|
C5
|
HPRD
|
Heating valve period or minimum on time
|
Secs/10
|
Depends on driver
|
1 to 240
|
C6
|
HDLY
|
Interlock delay
0: Battery starts with AHU Fan (no delay)
Negative value: for wet batteries, Valve opens before AHU Fan starts
Positive Value: for electric batteries, AHU Fan starts first runs on after
battery shuts down
|
Mins
|
0
|
-60 to 60
|
C7
|
CPRD
|
For future use; set to 10 for this application
|
Secs/10
|
10
|
1 to 60
|
C8
|
CDLY
|
For future use; set to 0 for this application
|
Mins
|
0
|
-30 to 30
|
C9
|
FPRD
|
Ffor future use; set to 12 for this application
|
Secs/10
|
12
|
1 to 60
|
C7
|
INMD
|
Input Mode for input terminals 3 and 4 ‘temp a’
0: Additional temperature input for max, min, ave using SACT
1: External occupation (input linked = Occupied) AND
with internal Occupation
2: External occupation (input linked = Occupied) OR
with internal Occupation
3: External Occupation signal only
4: Alarm input
5: Pump alarm
|
-
|
0
|
0 to 5
|
C10
|
MIND
|
Minimum demand used for pump output:
0: Pump runs for whole of AHU Occupancy period
>0: Pump runs only when Preheat demand exceeds MIND
|
|
4
|
0 to 100
|
C11
|
FRPT
|
Frost mode
0 no action
1 open valve
2: open valve and run pump (if fitted)
|
-
|
1
|
0 to 2
|
C12
|
MANL
|
Manual level , from Doorway
|
%
|
0
|
-100 to 100
|
C13
|
ALRM
|
Alarm mode
0 ignore alarms
1 report alarms
2 report alarms, shut down all outputs on alarm
3 report alarms, shut down all outputs on STOP alarm or sensor fail alarm
|
-
|
1
|
0 to 3
|
C14
|
ALST
|
not used
|
-
|
0
|
0 to 1
|
C15
|
MXVA
|
Maximum Voltage output a (for AOP types only)
|
V
|
10
|
0 to 10
|
C16
|
MNVA
|
Minimum Voltage output a (for AOP types only)
|
V
|
0
|
0 to 10
|
C17
|
MXVB
|
Maximum Voltage output b (for AOP types only)
|
V
|
10
|
0 to 10
|
C18
|
MNVB
|
Minimum Voltage output b (for AOP types only)
|
V
|
0
|
0 to 10
|
Doorway / InSite Code
|
Label
|
Description
|
Units
|
Default Value
|
Range
|
I1 (C30)
|
FRST
|
Frost Protection Mode
|
-
|
-
|
0 to 1
|
I2 (C31)
|
OCC
|
Occupied
|
-
|
-
|
0 to 1
|
I4 (C33)
|
EXTI
|
External Input
|
-
|
-
|
0 to 1
|
I6 (C35)
|
RLYA
|
Triac A Status
|
-
|
-
|
0 to 1
|
I7 (C36)
|
RLYB
|
Triac B Status
|
-
|
-
|
0 to 1
|
I8 (C37)
|
RLYC
|
Triac C Status
|
-
|
-
|
0 to 1
|
W1 (C38)
|
AUTO
|
Automatic/Manual Status
|
-
|
-
|
0 to 1
|
W2 (C39)
|
OVRD
|
Override
|
-
|
-
|
0 to 1
|
W5 (C42)
|
HAND
|
Manual Hand mode
|
-
|
0
|
0 to 1
|
W6 (C43)
|
POT
|
Potentiometer fitted to this board
|
-
|
0
|
0 to 1
|
W7 (C44)
|
SERV
|
Service Pin Msg (to Doorway +InSite, self resetting)
|
-
|
-
|
0 to 1
|
|
|
W1 and W2 used together with Doorway Auto/Manual dialog box
|
|
|
|
S1* (C50)
|
TEMP
|
Measured off coil temperature
|
Deg C
|
-
|
0 to 35
|
S2* (C51)
|
DMND
|
Controller output
|
%
|
-
|
-100 to 100
|
S3 (C52)
|
REQD
|
Controller current setpoint
|
Deg C
|
-
|
0 to 35
|
S4 (C53)
|
HDMD
|
Heating output demand
|
%
|
-
|
0 to 100
|
S5 (C54)
|
CDMD
|
Cooling Demand to valve or damper (shows position)
|
%
|
-
|
0 to 100
|
S6 (C55)
|
FDMD
|
Fan or Pump Demand
|
%
|
-
|
0 to 100
|
K1 (C60)
|
OCSP
|
Occupation Setpoint
|
Deg C
|
8
|
1 to 35
|
K2 (C61)
|
DEGR
|
Maximum temperature across battery with heating at 100%
|
Deg C
|
10
|
5 to 30
|
| |
|
* 24 hour plots available for these values by default
|
|
|
|
| |
|
Plotting interval and plotted variable changeable via Doorway or InSite
|
|
|
|
